Current Price: $34.04
Buy It Now Price: $34.04
Bids: 0

Astromania Alignment 1.25" Next Generation Laser Collimator 2" Adaptor for Newtonian Telescopes

Product Details

  • Product Dimensions: 8.27 x 3.34 x 2.37 inches
  • Item Weight: 4.8 ounces
  • Item model number: SKU_AM_ZAA10252
  • Is Discontinued By Manufacturer: No
  • Date First Available: August 17, 2015
  • Manufacturer: Astromania
  • Designed for Reflector telescope, with removable 2" adapter both fit for standard 1.25 inch diameter and 2 inch diameter. Red laser collimation beam with 7 brightness levels, wavelength 635-655 nm; Output power: less than 5mw, much safer for your eyes. This sturdy laser unit allows you to swiftly and precisely collimate your Newtonian telescope. Only when the optics have been accurately collimated can the telescope offer you its full performance.
  • Built with metal material. CR2032 Lithium Cell battery (Not include) ; Accurate collimation in a few minutes provide a more clearer image. The telescope can be collimated by just one person.
  • The precision-made aluminium housing of the laser unit has a front opening from which the laser beam can be emitted. In order to obtain an optimal adjustment, it has a side window allowing a disk oriented at 45 with a central hole to be viewed.This can be then later be used to see whether the laser is reflected back on itself, indicating well collimated optics.
  • This adjustment tool can be used in all 1.25" focusers. We provide you with precise instructions in German and English, with a step-by-step explanation of how to adjust a Newtonian telescope using this laser unit. So, even if you are a newcomer to amateur astronomy, it is very simple to get the optimum performance out of your telescope.
  • The laser comes fully adjusted. It can however be further adjusted if required. It has three openings for adjustment, arranged at 120, which are initially sealed. The battery for the laser can be exchanged at any time; the small screw cap at the rear of the laser must be first unscrewed to allow this.

Newtonian reflectors perform at their best when primary
and secondary mirrors are accurately aligned. Such alignment, called
collimation, is critical for achieving a sharp, highly resolved view through
the telescope. Collimation, while intimidating at first glance, is really not
difficult to do. And it’s made all the easier with the Laser Collimator! This
handy tool, designed specifically for collimating the optics of Newtonian
reflectors, provides a quick, easy way to a) determine if one or both of your
telescope’s mirrors need adjustment, and b) make the necessary adjustment(s)
quickly and easily. Before You Begin Collimating with the Laser
Collimator:Accurate collimation of your telescope’s optics using the Laser
Collimator will most easily be achieved if you do a rough collimation of the
optics with your eye first. This is because if the optics are grossly
misaligned, it may be confusing to interpret which surfaces the laser is being
reflected off of. This laser collimator uses a low wattage laser to project a
red beam down through the telescope’s focuser. The beam reflects off the
secondary mirror to the primary mirror, then bounces back up to the secondary
mirror and exits through the focuser onto the angled, bulls-eye viewing screen
of the collimator itself. The beam is generally not visible, but you’ll see a
bright red dot on each reflected surface. The Laser Collimator works equally
well to collimate telescope optics in daylight or at night in the dark. The
Laser Collimator has been precisely aligned within its housing at the factory.
Astromania Alignment 1.25" Next Generation Laser Collimator 2" Adaptor for
Newtonian Telescopes Adjusting Secondary Mirror: The first step in the
collimation procedure is to check the alignment of the secondary mirror and
adjust it if necessary. Insert the Laser Collimator into your telescope’s
focuser drawtube and secure it with the thumbscrew(s) on the drawtube collar.
Then turn the collimator on by turning the knob at the top to the On position.
Look down the front of the optical tube. Remember to keep your eyes clear of
any direct reflections of the beam. Notice the red spot on the surface of the
primary mirror itself; this is the laser beam being reflected from the
secondary mirror off the surface of the primary mirror. The red spot should be
centered in the collimation target (ring) on the mirror. If it isn’t,
adjustments will need to be made to the secondary mirror’s tilt. This is done
with the secondary mirror collimation screws, usually located on the central
hub of the telescope’s spider vane assembly. Make adjustments to the
telescope’s secondary mirror collimation screws until the reflection of the
laser beam is centered in the collimation target on the primary mirror.
Adjusting the Primary Mirror: The final collimation step is to adjust the tilt
angle of the primary mirror. Orient the collimator in the focuser so that the
viewing screen is facing the rear of the telescope. While standing at the rear
of the telescope, look over at the bulls-eye viewing screen of the collimator.
You should see the red laser dot somewhere on the viewing screen. If you
don’t, then the collimation is grossly off. In that case, place a piece of
paper in front of the open tube and note the position of the laser dot on the
paper. Make adjustments to the primary mirror collimation screws to move the
laser dot closer to the center and eventually onto the collimator’s bulls-eye
viewing screen. Once the laser dot is on the viewing screen, you can perform
the final collimation. Adjust the primary mirror collimation knobs until the
laser dot hits the center hole of the bulls-eye screen and pretty much
disappears, except for some red “spray” around the periphery of the hole. You
can make certainthe laser dot is properly aimed into the hole by slightly
adjusting one of the collimation knobs to bring the laser dot out of the hole,
then return it by turning the collimation screw the other way.Collimation of
the optical system is now complete! Go out and enjoy the view! Care and
Maintenance: Your Laser Collimator is manufactured of the highest quality
components. The internal laser diode is precision aligned with the mechanical
axis of the housing at the factory and tested to meet stringent
specifications. Like all electronic equipment, the Laser Collimator should be
handled with care. If it is dropped or handled roughly, the internal laser
could become misaligned. Avoid exposing the collimator to water, dust, heat,
or prolonged periods of direct sunlight. To extend battery life, store the
collimator in a cool, dry environment. Read more Installing a New Battery: The
Laser Collimator is powered by a single CR2032 3V lithium ion “button cell”
battery. When the laser beam starts to dim or completely fades, it’s time to
replace the battery. To do so, unscrew the knurled battery compartment cap at
the top of the collimator. With a knife tip or the end of a paper clip, lift
the edge of the expired battery out. Insert a fresh CR2032 battery with the
positive (+) side up. Then replace the cap. The CR2032 is a commonly used
battery in watches, calculators, cameras, and other electronic devices,




Filed under: Eyepieces & Accessories